Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
Everyone seems to have their own unique thinking with regards to Tools You Need to Install a New Bathtub .
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily available, the project can move rapidly; if you need to open a wall to get rid of the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and set in the brand-new one. Ensure you have actually certified on your own for the job and fit trying it. Rather than working with a professional to take over a halfway-completed job, it is much better to consider utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This post will aid you set up a new bath tub in your bathroom if you have actually currently gotten a brand-new tub and also do not require to alter the setup of your previous water system pipelines.
Your tools as well as product checklist should comprise the following:
Planning for the Installation
To start with, the supporting frame provided with the bath should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly bothersome because of the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipes have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water as well as check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as also examine the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub must wait up until the tub has been made use of at the very least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Secure the faucet in position with the producer given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with wetness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like more info about How to Install a Bathtub Yourself? Write feedback directly below. We will be delighted to listen to your reactions about this posting. Hoping that you visit us again in the future. Sharing is nice. You won't know, you could be helping someone out. Kudos for your time. Don't hesitate to pay a visit to our blog back soon.
Call Report this page